Modern Masters - Metallic Paint Collection - Exterior Satin - Quart
New Exterior Metallics are non tarnishing, water-based and formulated with the same shimmering particles and ease of application as our original Metallic Paint Collection. Available in 12 of the most popular colors for exterior architectural and commercial applications. Note: Allow 2-3 days for orders to ship.
We deliver nationwide, see expedited transit times and our shipping rates by entering your shipping info on the checkout page.
Modern Masters® Metallic Paint Collection™ provides a beautiful metallic look durable for exterior applications. This complete system includes two multi-surface primers, Cool and Warm Tone and 12 pre-mixed metallic paint colors. These colors can be applied by brush, roller or spray equipment to exterior architectural surfaces such as window mullions, exterior paneling and other architectural features. It’s water, mold, mildew, chemical, stain, mar, impact and UV resistant, so no additional protective top coat is needed. This product reduces the overall time and numbers of coats required to beautify and protect your project.
SURFACE PREPARATION: All surfaces to be painted must be entirely free of dust, dirt, oil, grease, and other contaminants. Completely remove all loose, flaking, or chalking paint from the surfaces. Use a NIOSH approved respirator when sanding and when working with old, loose paint particles. Provide adequate ventilation. Properly prime the clean, dry surface with a primer from our recommended list and allow the surface to dry completely— preferably overnight.
Warning! If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1- 800- 424-LEAD or log on to www.epa.gov/lead
NOTE: Always test the product in a small, inconspicuous area before beginning a project to see if the desired results are attained. We recommend preparing a sample board prior to beginning a project to check color and technique. The paint should be mixed thoroughly before using.
Modern Masters Metallic Paint Collection paints can be brushed, rolled, or spray applied (See specific equipment requirements under Spraying) onto any paintable, properly primed, interior or exterior surface, such as walls, ceilings, columns, trim, doors, furniture, and paintable wallcoverings.
Do not apply in temperatures below 58°F/14°C or above 85°F/29°C.
BRUSHING: Use a high-quality brush recommended for water-based semi-gloss paints.
Rolling: Use a high-quality 3/8 nap roller. Thoroughly clean the roller cover before beginning project. Work in sections, approximately 3-4 foot wide, keeping a wet-edge, cross roll to improve coverage, finishing the surface by back-rolling in one direction, top to bottom. This procedure will minimize lap marks, properly orient the metallic particles and give a uniform appearance.
Spraying: Use a NIOSH approved respirator when spraying. Provide adequate ventilation. To spray Metallic Paint Collection paints, thin with up to 16 fluid ounces/473 milliliters of water to one gallon/3.78 liters of Metallic Paint Collection paints. Thin carefully, as over thinning of the paint will result in loss of hide and a reduction of the desired appearance.
Use an HVLP gun or a conventional cup gun with the fluid and air supply from a pressure pot and compressor. Air pressure at the HVLP spray gun needs to be approximately 45 psi, with greater pressures at the tank, approximately 60 psi.
Binks Mach 1 HVLP, with a 94-nozzle set up (0.55 or 1.4mm diameter fluid tip and a 90P air nozzle). The settings for this equipment were: Fluid Pressure-25psi and Air Pressure-45psi.
Binks- 2001 Conventional, with a 66SS air nozzle set up (0.70 or 1.8 fluid tips and a 66SD air nozzle). The settings for this equipment were: Fluid Pressure-30psi and Air Pressure-60psi.
Note: Do not use turbine-type “air compressors” to power the HVLP spray gun and do not use airless spray systems.
Taping – Use high quality, low-tack tape when taping over surfaces that have been previously painted with Metallic Paint. When painting over taped-off areas be aware that Metallic Paints exhibit poor early adhesion properties and are elastomeric (They stretch) during curing. Because of these two factors consider cutting along the tape edge with a razor blade to avoid delaminating the fresh paint from the substrate.
Tinting – Exterior Metallic Paint Collection Colors can be intermixed to create custom colors.
Dry Times – Recoat time is approximately ½ hour. Dry-totouch time is approximately an hour. (Drying times were recorded at 70°F and 50%RH) Note: Lower temperature and/or higher humidity will lengthen the dry and cure times.
Coverage – One gallon will cover approximately 320 to 400 square feet. Approximately 1.5 mils dry film thickness per coat. A minimum of 3 mils dry film thickness is required for hide and full color development.
Clean Up – Clean brushes, rollers, tool, and equipment with soap and warm water immediately after use. Do not reuse containers and properly dispose of empty containers.
We make it our mission to ship your order in a timely fashion. Due to the nature of our business and the wide variety of our product offerings we sometimes encounter stock issues. Should there be any issues getting your order shipped we will contact you to update you on the situation.
All in stock items ship within 24 business hours. If you need your order shipped sooner than that please contact us directly before placing your order.
- FedEx Priority Overnight
- FedEx Standard Overnight
- FedEx 2Day A.M
- FedEx 2Day
- FedEx Express Saver
- FedEx Ground
- Local In Store Pickup