Sheen Levels: 

Matte - measured 10-20 @ 60° 

Satin - measured 25-35 @ 60° 

Semi-Gloss - measured 50-60@ 60° 

Gloss - measured >80 @ 60° 

Where To Use: 

Interiors: Protects painted surfaces, wallpaper, bare wood, oil and water based stained wood, doors, columns, cabinetry, window sills, mantels, wainscot, wood paneling, crown molding, baseboards, chair rails, furniture and picture frames. It is a perfect clear coat for faux marble and wood grained surfaces. 

Exteriors: UV and weather resistant, it extends the life of previously painted surfaces, stained or unstained wood and aluminum surfaces such as doors, porch surrounds and supports, decorative moldings, painted facades, murals, garage doors, anodized aluminum window casings, aluminum paneling, outdoor furniture and garden ornaments. 

MasterClear Supreme is not recommended for surfaces painted with Metallic Paint Collection™, white or light colored surfaces or for use on floors. 

Taping – Use high quality, low-tack tape when taping over surfaces that have been previously painted and fully cured. 

Dry Times – Dry-to-touch time is approximately 1/2 hour. Tack free in one hour. Recoat time is approximately 1-2 hours (drying times were recorded at 70°F and 50%RH): Note: Lower temperature and/or higher humidity will lengthen the dry and cure times. 

Coverage – One gallon/3.78 liters will cover approximately 300 to 400 square feet/27 to 37 square meters, approximately 1 mil dry film thickness per coat. For best results and maximum protection apply a minimum of two coats and on surfaces in extreme weather conditions apply three coats. 

Clean Up – Clean brushes, rollers, tool, and equipment with soap and warm water immediately after use. Do not reuse containers and properly dispose of empty containers. 

Surface Preparation – Painted Surfaces should be fully cured prior to application, clean, dry and free from dust, rust, stains, grease, oil, mildew, wax, efflorescence and other contaminants. 

Bare Wood should be prepared by first sanding the surface smooth, removing dust with a vacuum and then wiping the surface clean with an oil-free tack cloth. Moisten the wood surface with a wet towel or sponge and allow it to dry. When dry, sand the raised grain with fine sandpaper until smooth, then vacuum and wipe clean with the oil-free tack cloth. 

Oil Base or Water Base Stained Wood: Follow stain manufacturer’s instructions for application and dry times for clear coating with a water based poly. Make sure the stain has been wiped off the surface completely and has dried a minimum of 24 hours before applying MasterClear Supreme. 

Aluminum: Clean the aluminum. The amount of cleaning will depend on the condition of the anodized aluminum. If window frames or extruded anodized aluminum is just dull or faded, it can be washed with mild soap and water. Use microfiber cloths which are inexpensive and will clean the metal very effectively. If the anodized aluminum is pitted or stained, use a noscratch cleanser or synthetic steel wool made by 3M (do not use regular steel wool , small pieces can remain on window frames and will rust). Rinse well. Let dry. If any oxidation remains, wipe with the microfiber cloth. Finally, wipe down the anodized aluminum with Technical Data Sheet Modern Masters September 2013 Page 2 of 2 denatured alcohol and wear neoprene gloves to protect your hands. 

Application – Stir thoroughly before use, do not shake. MasterClear Supreme can be brushed, rolled or spray applied. Sand between coats to achieve the smoothest finish. Optimal conditions are 60°F/16°C to 80°F/27°C and 30% to 60% relative humidity. Do not apply in temperatures below 55°F/13°C or above 95°F/35°C. 

Brushing: Use a high-quality synthetic bristle brush. 

Rolling: Use a high-quality short nap varnish roller 

Spraying: To spray, thin with up to 10%, 12 fluid ounces/360 ml of water to one gallon/3.78 liters of MasterClear Supreme. Use an HVLP gun, conventional cup gun or airless spray system with a fine tip. 

We make it our mission to ship your order in a timely fashion. Due to the nature of our business and the wide variety of our product offerings we sometimes encounter stock issues. Should there be any issues getting your order shipped we will contact you to update you on the situation. 

All in stock items ship within 24 business hours. If you need your order shipped sooner than that please contact us directly before placing your order.

• FedEx Priority Overnight
• FedEx Standard Overnight
• FedEx 2Day A.M
• FedEx 2Day
• FedEx Express Saver
• FedEx Ground
• Local In Store Pickup 

Material VOC – Contains less than 50 g/L. 

Handling & Storage – To avoid skinning, close container after each use. Keep lid tightly closed during storage. Keep away from excessive heat. Protect from freezing. If contents freeze, allow to thaw and come to room temperature before use. Stir thoroughly before use. 

Disposal – Dispose of unused or unwanted product in accordance with local laws regulating water-based coatings. 

Health & Safety – Use in a well-ventilated area. Avoid contact with eyes. Wash hands thoroughly with soap and warm water after use. Do not take internally. When spraying or sanding, use a properly-fitting, NIOSH approved respirator per the manufacturer’s instructions. 

Skin contact: Thoroughly wash with soap and warm water before the coating dries. Individuals with sensitive skin may require gloves. 

Eye contact: Rinse with clean water for 15 minutes. Seek medical attention. 

Inhalation: To help prevent irritation, use only in well ventilated areas. If irritation occurs, move to fresh air. If irritation persists, seek medical attention. 

Ingestion: Do not induce vomiting. Seek medical attention. 

Read the Material Safety Data Sheet for Additional Health and Safety Information.