Reach out to us for pallet orders and bulk pricing.

Richard's - EXCEL 100% Acrylic DTM - Semi-Gloss

Score: 5.00 (votes: 1)
No reviews.
5.00

A professional quality waterborne corrosion resistant coating for light to moderate industrial and commercial use. Formulated using state-of-the-art hybrid acrylic polymer resins, it provides superior high performance qualities, similar to alkyd-based industrial enamel coatings.

  • White
    Black
    Color: not selected
  • $52.09
Qty:  

It offers superior flow and leveling characteristics, excellent coverage, and dries to a hard, tile-like gloss finish that provides excellent durability. It resists moisture, salt spray, alkali, mildew, mild chemical washings, staining, fading and corrosion. Its special formulation also allows for use as a direct-to-metal industrial acrylic enamel to a variety of both interior and exterior properly prepared metal and architectural substrates. It is easy to apply, rust inhibitive, wear and chip resistant, and is available in OSHA approved safety colors for identification purposes. 

PRODUCT FEATURES

  • 100% Acrylic Formula 
  • Tile-Like Gloss Finish 
  • Excellent Durability 
  • Excellent Coverage 
  • Moisture Resistant 
  • Mildew Resistant 
  • Rust Inhibitive 
  • Excellent Product Versatility

INTERIOR/EXTERIOR 

  • Gypsum Drywall 
  • Plaster • Wood Doors & Trim 
  • Metal Doors & Trim 
  • Masonry 
  • Ferrous Metal 
  • Non-Ferrous Metal 
  • Storage Tanks 
  • Aluminum 
  • Fiberglass

GENERAL: The entire surface area to be painted should be clean, dry, sound, and free from dirt, grease, oils, waxes, mildew and any other surface contaminants that may adversely affect the performance of this coating material. 

PREVIOUSLY PAINTED SURFACES: Remove any loose, scaling, cracked or peeling paint from previously painted surfaces by hand scraping, sanding, wire brushing or by power tool cleaning methods, such as electric sanders or grinders, etc. Sand all rough paint edges smooth to adjacent surface area. Sand all glossy surfaces to dull existing finish. Spot prime all bare surface areas with same primer material and allow to thoroughly dry before applying finish coatings. 

SURFACE REPAIRS: Repair/replace any damaged and/or delaminated surface areas with the proper recommended patching and/or building materials. Allow patching materials to dry thoroughly before application of paint coatings 

METAL SURFACES: Remove all surface contaminants, oil and grease in accordance with SSPCSP1. Remove any loose rust, mill scale, rust deposits or white rust from metal surface in accordance with SSPC-SP 2 – Hand Tool Cleaning specifications, or by power tool cleaning methods, such as electric sanders or grinders according to SSPC-SP 3 – Power Tool Cleaning specifications, as set forth by The Society for Protective Coatings. Previously painted surfaces, whereby the existing paint show signs of serious deterioration should be completely removed in accordance with SSPC-SP 6 – Commercial Blast Cleaning, or SSPCSP 10 – Near White Blast Cleaning specifications. 

DRYWALL: Insure that the surface is dust & chalk free, and primed with recommended primer. 

MASONRY / CONCRETE: All new masonry surfaces should be allowed 30 – 90 days to properly dry/cure in accordance with industry standards. The surface should be tested for pH and alkali levels. Surface should not read higher than 8.5 – 9 level. 

WOOD: All new wood surfaces must be clean, dry and sound, and should be properly primed and painted before installation or immediately after. Remove any grade stamps or pencil marks from new wood by lightly sanding. Wood moisture content should be below 15% and wood surfaces that have a mill glaze should be sanded to allow for proper adhesion. 

MILDEW: Surface areas affected by mildew should be treated with a commercial mildew removal and/or wash product carefully following manufacturer’s application and safety directions. Rinse thoroughly with clean water, and allow a minimum of 24 hours to dry thoroughly.

Richard’s EXCEL Rust Shield 100% Acrylic DTM Industrial Gloss Enamel may be easily applied with a quality brush, roller, or spray equipment as follows; 

Stir thoroughly in a spiral up and down motion before and during application to keep product completely mixed. 

For best results, it is recommended to apply two finish coats. 

To assure color uniformity always intermix multiple containers of custom tinted and stock colors. Apply a small test sample to verify color. 

Always paint to a natural break in the surface, such as a corner or edge. 

Brush Applications: When applying by brush, use a quality nylon or polyester bristle brush, or a quality combination of both, and apply a smooth and generous coat on smaller surface areas, such as cutting-in larger surfaces and painting trim. 

Roller Application: When applying by roller cover, use a quality smooth, medium or rough nap roller, depending on surface porosity, and apply an even and generous coat in a “W” or crisscross motion, avoiding any excessive respreading or reworking. 

Spray Application: When applying by airless spray equipment, use a unit with a minimum of 2000 psi of pressure, with a 0.013 – 0.017 fluid spray tip. 

Rough or textured surfaces coated using spray equipment should be backrolled to ensure a uniform film, even coverage and proper adhesion. 

Maintain a wet edge during application by brushing, rolling or spraying into previously applied coating area. 

Apply when surface and ambient temperatures are above 55º F and below 90º F. Do not apply when surface and air temperature is within 5° of the dew point. 

Avoid exterior paint application when weather conditions are threatening, and late in the day when there is a threat of moisture condensing on wet paint.

Related products