Seal Krete - 401003 - 40Lb Floor Tex
SEAL-KRETE® FLOOR-TEX® Textured Concrete Coating is a durable, non-slip, texture coating that provides a decorative finish for concrete and masonry surfaces such as pool decks, patios, porches, ramps and walkways.
We deliver nationwide, see expedited transit times and our shipping rates by entering your shipping info on the checkout page.
Paintable and tintable, this premium acrylic formula hides surface imperfections while providing a tough finish that resists damage from moisture, salt, oil, gas and chlorine. Performance-tested on commercial traffic sites, Floor-Tex outwears conventional anti-skid coatings, paints and stains. It’s also suitable for wood stairs.
- Choose Your Color - Just Add One Gallon of Seal-Krete Epoxy-Seal or Garage Floor Paint
- Non-Slip Decorative Finish for Concrete & Masonry Surfaces
- Resistant to Moisture, Salt, Chlorine and Oil
- Hides Imperfections, Stains & Discolorations
- Meets ADA Requirements for Non-Slip Coatings
- Brush, Roll or Spray
Note: Proper surface prep is critical to product performance. The surface should be clean, dry, sound and free of dirt, dust, oil, wax and grease. You may need an oil stain remover such as SEAL-KRETE Oil Stain Remover to lift stubborn oil stains.
Bare Concrete: Concrete must have cured for a minimum of 30 days before application. Etch the surface with SEAL-KRETE Clean-N-Etch to allow for proper penetration and adhesion. Etching is especially important for smooth-troweled concrete surfaces and is also recommended for rough finished surfaces. After etching, rinse thoroughly and let dry. For best results apply one thin coat of SEAL-KRETE Lock-Down Concrete Bonding Primer.
Surface Cracks: Use a paintable acrylic or urethane caulk to repair hairline cracks. For other cracks (up to 3/8" wide) use a flexible, acrylic concrete patch or filler. Let all materials cure fully.
Previously Stained or Painted Concrete: For use over one-part water-based coatings only; not recommended over oil-based coatings. Remove loose or peeling paint and degloss surface by sanding (150–200 grit sandpaper).* Follow with a general cleaning. Rinse thoroughly and let dry. Then coat the surface with SEAL-KRETE Lock-Down Concrete Bonding Primer.
Add 1 gallon of acrylic concrete & garage floor paint, such as SEAL-KRETE Epoxy-Seal, to 40 lb. Floor-Tex and mix thoroughly with a paint mixing blade attached to a 3/8" electric or 18-volt cordless drill (if not premixed by store paint shaker). Carefully pour into a clean, deep-welled paint tray. Use only when air and surface temperatures are 50° to 90°F (10° to 32°C). A minimum of 2 coats is recommended. Apply first coat and let dry to touch, then apply second coat in direction perpendicular to the first.
Brush: Use a high quality, nylon bristle brush.
Roller: Use a short nap (1/8", 3/16" or 1/4") cover – synthetic or mohair blend.
COVERAGE: 40 lb. Floor-Tex with paint added will cover approximately 300 sq. ft. in two coats, depending on the substrate porosity and thickness applied.
DRY TIME: Dry to touch in 1–4 hours. Dry to foot traffic in 24 hours. Will accept vehicular traffic in 3–5 days. Note: Dry times vary depending on temperature and humidity.
TOPCOATING: To finish the system and for easier maintenance, wait 24 hours before applying one thin coat of SEAL-KRETE Clear-Seal.
CLEAN-UP & STORAGE: Clean all tools immediately after use with soap and water. Store unused product in a dry place above 32°F (0°C). KEEP FROM FREEZING.
We make it our mission to ship your order in a timely fashion. Due to the nature of our business and the wide variety of our product offerings we sometimes encounter stock issues. Should there be any issues getting your order shipped we will contact you to update you on the situation.
All in stock items ship within 24 business hours. If you need your order shipped sooner than that please contact us directly before placing your order.
- FedEx Priority Overnight
- FedEx Standard Overnight
- FedEx 2Day A.M
- FedEx 2Day
- FedEx Express Saver
- FedEx Ground
- Local In Store Pickup